manualshive.com logo in svg

Avaya 4524GT, Configuration Manual

Share
Download
Avaya 4524GT Configuration Manual Download Page 106

Run the 

stack auto-unit-replacement enable

 command in Global Configuration

mode.

No parameters or variables are available for the 

stack auto-unit-replacement enable

command.

no stack auto-unit-replacement enable command

The 

no stack auto-unit-replacement enable

 command disables AUR on the

switch.

The syntax for this command is

no stack auto-unit-replacement enable

Run the 

no stack auto-unit-replacement enable

 command in Global Configuration

mode.

No parameters or variables are available for the 

no stack auto-unit-replacement

enable

 command.

default stack auto-unit-replacement enable command

The 

default stack auto-unit-replacement enable

 command restores the default

AUR settings.

The syntax for this command is

default stack auto-unit-replacement enable

Run the 

default stack auto-unit-replacement enable

 command in Global

Configuration mode.

No parameters or variables are available for the 

default stack auto-unit-

replacement enable

 command.

stack auto-unit-replacement config save enable

The 

stack auto-unit-replacement config save enable

 command enables

automatic configuration saves for non-base units.

No parameters or variables are available for the 

stack auto-unit-replacement config

save enable

 command.

System configuration using ACLI

106     Configuration — System

April 2011

Summary of Contents for 4524GT











































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands