manualshive.com logo in svg

Avaya 4524GT, Configuration Manual

Share
Download
Avaya 4524GT Configuration Manual Download Page 168

Variables

Description

med

The Media Endpoint Device (MED) for a specific
TLV.

lldp tx-tlv dot1 command

The 

lldp tx-tlv dot1

 command sets the optional IEEE 802.1 organizationally-specifc

TLVs to be included in the transmitted LLDPDUs. The syntax for the 

lldp tx-tlv dot1

command is

(config)#lldp tx-tlv [port <portlist>] dot1 [port-protocol-vlan-id
<vlanlist>] [port-vlan-id ] [protocol-identity < [EAP] [LLDP] [STP]>]
[vlan-name <vlanlist>]

The 

lldp tx-tlv dot1

 command is in the Interface Configuration command mode.

The following table describes the variables for the 

lldp tx-tlv dot1 

command.

Table 78: lldp tx-tlv dot1 command variables

Variables

Description

port <portlist>

The ports affected by the command.

port-protocol-vlan-id <vlanlist>

The port and protocol VLAN ID TLV.

port-vlan-id

The port VLAN ID TLV.

protocol-identity <[EAP] [LLDP]
[STP]>

Protocol Identity TLV

vlan-name <vlanlist>

The VLAN name TLV.

lldp tx-tlv dot3 command

The 

lldp tx-tlv dot3

 command sets the optional IEEE 802.3 organizationally-specifc

TLVs to be included in the transmitted LLDPDUs. The syntax for the 

lldp tx-tlv dot3

command is

(config-if)#lldp tx-tlv [port <portlist>] dot3 [link-aggregation]
[mac-phy-config-status] [maximum-frame-size][mdi-power-support]

Run the 

lldp tx-tlv dot3

 command in Interface Configuration command mode.

The following table describes the variables for the 

lldp tx-tlv dot3

 command.

System configuration using ACLI

168     Configuration — System

April 2011

Summary of Contents for 4524GT











































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands