Avaya 4524GT Configuration Manual Download Page 292

Page: 292 / 362

Viewing LLDP local system information using EDM

Use the following procedure to display LLDP properties for the local system.

Procedure steps

1. From the navigation tree, double-click

Edit

2. In the Edit tree, double-click

Diagnostics

3. In the Diagnostic tree, double-click

802.1AB

4. In the 802.1AB tree, double-click

LLDP

5. On the work area, click the

Local System

tab.

Variable definitions

The following table describes the Local System tab fields.

Variable

Value

ChassisIdSubtype

Indicates the type of encoding used to identify the local
system chassis:

• chassisComponent

• interfaceAlias

• portComponent

• macAddress

• networkAddress

• interfaceName

• local

ChassisId

Indicates the chassis ID.

SysName

Indicates the local system name.

SysDesc

Indicates the local system description.

SysCapSupported

Indicates the system capabilities supported on the
local system.

SysCapEnabled

Indicates the system capabilities that are enabled on
the local system

DeviceClass

Indicates the MED device class.

System configuration using Enterprise Device Manager

292 Configuration — System

April 2011

Summary of Contents for 4524GT











































































































































































































































































































































































Search results

Summary of Contents for 4524GT

Reviews:

Brands by name

Popular brands

Avaya 4524GT, Configuration Manual

Search results

Summary of Contents for 4524GT

Reviews:

Brands by name

Popular brands