Avaya 4524GT Configuration Manual Download Page 109

Page: 109 / 362

show stack auto-unit-replacement-image command

Use the

show stack auto-unit-replacement-image

command to view the current

status of the AAUR functionality.

The syntax of this command is

show stack auto-unit-replacement-image

Run the

show stack auto-unit-replacement-image command

in User EXEC

command mode.

Configuring DAUR

There are no commands to separately enable or disable DAUR.

Setting Stack Forced Mode

This section describes the procedures and commands to configure Stack Forced Mode on a

two unit stack.

Use ACLI Global Configuration command mode to configure Stack Forced Mode.

This section contains the procedures to configure

stack forced-mode

Configuring stack forced-mode

Use the following procedure to configure

stack forced-mode

1. Enter

stack forced-mode

2. Press

Enter

Job aid

The following table defines the options for the

stack forced-mode

command.

Table 39: Options for stack forced-mode

Option

Definition

Enable Stack Forced Mode.

Setting Stack Forced Mode

Configuration — System

April 2011 109

Summary of Contents for 4524GT











































































































































































































































































































































































Search results

Summary of Contents for 4524GT

Reviews:

Brands by name

Popular brands

Avaya 4524GT, Configuration Manual

Search results

Summary of Contents for 4524GT

Reviews:

Brands by name

Popular brands