Avaya 4524GT Configuration Manual Download Page 120

Page: 120 / 362

Disabling IPv6 interface

Use the following procedure to disable the IPv6 interface:

Enter the following command to disable IPv6.

no ipv6 interface [address <ipv6_address>] [all] [enable]

Displaying the global IPv6 configuration

Use the following procedure to display the IPv6 global configuration:

Enter the following command to display the global IPv6 configuration.

show ipv6 global

Job aid

The following graphic shows a possible result of the

show ipv6 global

command.

4526(config)#show ipv6 global

forwarding

: disabled

default-hop-cnt

: 30

number-of-interfaces

: 1

admin-status

: enabled

icmp-error-interal

: 1000

icmp-error quota

: 50

icmp-redirect-msg

: disabled

icmp-unreach-msg

: disabled

multicast-admin-status

: disabled

The following table describes the default settings for the fields in the graphic.

Field

Default setting

forwarding

disabled

default-hop-cnt

number-of-interfaces

admin-status

enabled

System configuration using ACLI

120 Configuration — System

April 2011

Summary of Contents for 4524GT











































































































































































































































































































































































Search results

Summary of Contents for 4524GT

Reviews:

Brands by name

Popular brands

Avaya 4524GT, Configuration Manual

Search results

Summary of Contents for 4524GT

Reviews:

Brands by name

Popular brands