manualshive.com logo in svg

Avaya 4524GT, Configuration Manual

Share
Download
Avaya 4524GT Configuration Manual Download Page 116

show ipv6 interface

Enter 

show ipv6 interface

.

Job aid

The following graphic shows the results of the 

show ipv6 interface

 command.

Displaying IPv6 interface addresses

View IPv6 interface addresses to learn the addresses.

Prerequisites

Log on to the User EXEC mode in ACLI.

Display IPv6 interface addresses

Use the following command to display IPv6 interface addresses:

show ipv6 address interface [vlan <1-4094> | <WORD 0–45>]

Variable definitions

The following table list the variables and definitions.

System configuration using ACLI

116     Configuration — System

April 2011

Summary of Contents for 4524GT











































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands