manualshive.com logo in svg

Avaya 03-300686, Installation And Connection, Page: 5 / 156

Share
Download
Avaya 03-300686 Installation And Connection Download Page 5

Contents

Issue 3 January 2008

5

Dual wiring of 2-wire and 4-wire endpoints  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

87

Installing the attendant console   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

87

Installing the 26B1 Selector Console   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

88

Connecting external alarm indicators and auxiliary power    .  .  .  .  .  .  .  .  .  .  .  .  

88

Installing off-premises station wiring   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

90

Off-premises or out-of-building stations    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

91

Off-premises connections   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

91

Off-premises protection requirements    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

93

Telephone restrictions for exposed environments  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

94

Digital Out-of-Building Telephone Protection .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

94

Installing the ITW Linx Enhanced Protector .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

95

Installing the 4C3S-75 Enhanced Protector  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

95

Installing the data link protector  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

95

Emergency transfer units and associated telephones  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

96

808A Emergency Transfer Panel and

telephone installation examples   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

97

Installing the 808A Emergency Transfer Panel  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

99

Installing telephones used only for

emergency transfer (trunk/auxiliary field)   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   104

Installing telephones used for emergency

transfer and as normal extension (trunk/auxiliary field)    .  .  .  .  .  .  .  .  .  .  .   105

Installing external ringing    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   106
Installing the queue warning indicator    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   107

Chapter 7: Installing and wiring telephone power supplies  .  .  .  .  .  .  .  109

1145B2 power supply  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   109

Important warning for 1145B2 power supply   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   110
Mounting the 1145B2/1146B2 power supply    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   111
Installing the wall-mounting plates    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   114
Mounting the 1146B2 Power Distribution Unit   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   114
Installing the battery mounting/wiring .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   115
Installing the expanded power distribution unit    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   115
Powering up and testing the power supply  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   116
Wiring the 1146B2 Power Distribution Unit  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   117
Resetting LEDs on power distribution unit   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   118

1152A1 Mid-Span Power Distribution Unit .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  

119

Important safety instructions .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   119
Using the 1152A1 Power Distribution Unit .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   120
Connecting the 1152A1 Power Distribution Unit   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   120
Connecting the cables   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   121

Summary of Contents for 03-300686





























































































































































Reviews:

No comments