Avaya 03-300686 Installation And Connection Download Page 150

Page: 150 / 156

Testing the complete configuration

150 Installing and Connecting the MDF and Telephones

SPAN LEDs

The four SPAN LEDs indicate the status of the four T1/E1 facilities. A SPAN LED is in one of the
following states:

●

Solid on yellow: Facility is operational and alarm free.

●

Blinking yellow for 2 seconds, off 0.1 seconds: Facility is operational and alarm free AND is
carrying the control channel (facility A or B only).

●

Solid on red: Facility is alarmed.

●

Solid off: Facility is not administered or has been busied out.

solid on

DS1 Converter

active. This is the normal state for an active

DS1

Converter

solid off

DS1 Converter

standby. This is the normal state for a standby

DS1 Converter

in critical reliability configurations (duplicated

PNC).

Table 23: DS1 Converter yellow LED flashing states (continued)

LED on

LED off

Condition

2 of 2

Summary of Contents for 03-300686





























































































































































Search results

Summary of Contents for 03-300686

Reviews:

Avaya 03-300686, Installation And Connection, Page: 150 / 156

Search results

Summary of Contents for 03-300686

Reviews: