manualshive.com logo in svg

Avaya 03-300686, Installation And Connection, Page: 106 / 156

Share
Download
Avaya 03-300686 Installation And Connection Download Page 106

Installing and wiring telephones and trunks

106 Installing and Connecting the MDF and Telephones

 

Installing external ringing 

Connections for external ringing are at an information outlet. The media gateway side of the 
MDF is connected to a TN2183 (or equivalent) Analog Line circuit pack. The circuitry and power 
source for the device are provided by the customer.

Note:

Note:

A maximum of three devices can connect to one analog line circuit pack port.

To install external ringing:

1. Wire the ringing device to the information outlet as shown in 

Figure 51: 3-pair and 4-pair 

modularity

on page 106 and 

Figure 41: Example adjunct power connections

on page 85.

2. Administer per the 

Administrator Guide for Avaya Communication Manager

 (03-300509).

Figure 51: 3-pair and 4-pair modularity

Figure notes:

1. Port Circuit Pack
2. Media Gateway Connector Pins

(3-Pair Modularity)

3. Main Distribution Frame (MDF) 

Pins (3-Pair Modularity)

4. Input to Information Outlet 

(4-Pair Modularity)

5. Adjunct Power
6. Output From Information Outlet 

(4-Pair Modularity)

7. Voice or Data Terminal Pins

Summary of Contents for 03-300686





























































































































































Reviews:

No comments