manualshive.com logo in svg

Avaya 03-300686, Installation And Connection, Page: 12 / 156

Share
Download
Avaya 03-300686 Installation And Connection Download Page 12

Introduction

12 Installing and Connecting the MDF and Telephones

 

●

Maintenance Commands for Avaya Communication Manager 5.0, Media Gateways and 
Servers, 

(03-300431). Provides information on how to use command interfaces, command 

syntax, and output from maintenance-related commands.

●

Maintenance Alarms for Avaya Communication Manager 5.0, Media Gateways and 
Servers, 

(03-300430). Provides information on how to use alarms, error codes, and tests 

to diagnose and repair problems.

●

Maintenance Procedures for Avaya Communication Manager 5.0, Media Gateways and 
Servers 

(03-300432). Provides information on how to troubleshoot and replace various 

components.

●

The following job aids are also available on the CD-ROM 

Documentation for Avaya 

Communication Manager, Media Gateways and Servers

:

-

Approved Grounds. 

Provides a description of all approved grounds.

-

Connector and Cable Diagrams (Pinout Charts). 

Provides pinout information for various 

components.

-

Option Switch Settings. 

Provides settings for various components.

For all documents associated with the S8400, S8500, S8700-series Server, see the CD titled 

Documentation for Avaya Communication Manager, Media Gateways and Servers

 (03-300151).

Summary of Contents for 03-300686





























































































































































Reviews:

No comments