manualshive.com logo in svg

Avaya 03-300686, Installation And Connection, Page: 24 / 156

Share
Download
Avaya 03-300686 Installation And Connection Download Page 24

Installing the main distribution frame

24 Installing and Connecting the MDF and Telephones

 

Mounting 110P-type terminal blocks on a frame 

The 900-pair 110P-type terminal blocks and the associated patch cord troughs can also be 
mounted on a free-standing, floor-mounted 1110A2 Apparatus Mounting Frame. See 

Figure 7: 1110A2 and 1110C1 apparatus mountings

on page 24.

Each 1110A2 provides the space to mount five terminal blocks/patch cord troughs on each side 
of the frame. A cable support structure, apparatus mounting 1110C1, mounts directly on top of 
the 1110A2 and provides support for all cables routed to and from the frame. See 

Table 1: Apparatus mounting frame ordering information

on page 25.

Figure 7: 1110A2 and 1110C1 apparatus mountings

Figure notes:

1. 1110C1 Apparatus Mounting
2. 1110A2 Apparatus Mounting
3. 76 inches (193 centimeters)

4. 88.5 inches (225 centimeters)
5. 43.5 inches (110.5 centimeters)

r781401 LJK 040896

Summary of Contents for 03-300686





























































































































































Reviews:

No comments