manualshive.com logo in svg

Avaya 03-300686, Installation And Connection, Page: 142 / 156

Share
Download
Avaya 03-300686 Installation And Connection Download Page 142

Testing the complete configuration

142 Installing and Connecting the MDF and Telephones

 

Figure 66: Sample of port network status after expansion link is set

Saving translations, if required

●

Type 

save translations

 and press 

Enter

 to save the translations to the hard drive.

Testing telephones and other equipment

This section describes how to test the telephones and other equipment. Perform these tests 
after the equipment has been wired to the media gateway and after the customer’s data for that 
equipment has been administered. The tests are acceptance tests and provide some assurance 
that the system will perform properly after installation and administration. 
If problems occur or more extensive tests are required, see the maintenance book for your 
configuration.
Perform these tasks to complete acceptance tests:

●

Making test calls

on page 143

●

Testing 302C attendant console

on page 143

●

Testing selector console

on page 144

status port-network
                              PORT NETWORK STATUS

   Major  Minor  Warning Carrier   PN Control      FIBER-
PN Alarms Alarms Alarms  Locs   Active   Standby   LINK     Endpoints   Mode

1    1      0      220   01A    up       up        1  B-PNC 01B02-03E04 standby
                         01B                       1  A-PNC 01A01-01E04 active

TDM Service  Control  Dedicated              TONE/  Service  System   System
Bus  State   Channel   Tones                 CLOCK  State    Clock    Tones

 A   in         y        n                   01B     in      standby  standby
 B   in         n        y                   01A     in      active   active

                Service     Major   Minor   Bus    Open Bus
           PKT  State       Alarms  Alarms  Faults  Leads

           1       in         n       n       0        0

Command: 

Summary of Contents for 03-300686





























































































































































Reviews:

No comments