manualshive.com logo in svg

Avaya 03-300686, Installation And Connection, Page: 131 / 156

Share
Download
Avaya 03-300686 Installation And Connection Download Page 131

1151B1 and 1151B2 Power Supplies

Issue 3 January 2008

131

 

Connecting the cables

To connect IP telephones, PCs, servers, routers, workstations, and hubs.

1. Connect the Ethernet connection cable (not supplied) to a 10/100 megabits per second port 

on the front panel of the Avaya C360 series switch. 

Note:

Note:

Use standard RJ45 connections and a CAT5 cable for 100 megabits per second 
operation.

2. Connect the other end of the cable to the Ethernet port of the PC, server, router, 

workstation, IP telephone, switch, or hub.

3. Check that the appropriate link (LNK) LEDs light up.

1151B1 and 1151B2 Power Supplies 

The 1151B1 and 1151B2 power supplies are a local power supply. The telephones or consoles 
connect directly to them through an RJ45 connector. The 1151B2 has a battery backup.
These power supplies comply with the 

Underwriters Laboratories Inc. (UL) 

Standard UL 

60950 third edition.

For safety instructions, see 

Important safety instructions for 1151B1 and 1151B2 Power 

Supplies

on page 132. For installation instructions, see 

Connecting the 1151B1 or 1151B2 

Power Supplies

on page 133.

Complies

UL 60950

Certified

CSA

 C22.2

Approved

EN

Approved

CE Regulatory Compliance

Summary of Contents for 03-300686





























































































































































Reviews:

No comments