Autel MaxiCOM MK808 Manual Download

Page: 112 / 168

105

4. Tap the

Home

button on the top left corner to return to the

MaxiCOM Job Menu, or tap another setting to adjust.

Printing Setting

Configure this option to enable the tablet to print through a specified Wi-Fi
network connection.



To setup the printer connection

1. Tap the

Settings

application on the MaxiCOM Job Menu.

2. Tap the

Printing Setting

option on the left column.

3. Tap the

Print via Network

item to activate the printing function,

which enables the device to send files to the printer through the
networked PC via Wi-Fi connection.

4. Tap the

Home

button on the top left corner to return to the

MaxiCOM Job Menu, or tap another setting to adjust.

Figure 8-3

Sample Printing Setting Screen

Printing via APP

MK808TS provides the most convenient printing method, printing via APP.

To realize this function, please make sure a Wi-Fi printer is available and
then purchase a Wi-Fi printer APP and install it onto your tablet.

Summary of Contents for MaxiCOM MK808









































































































































































Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands

Autel MaxiCOM MK808, Manual

Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands