Autel MaxiCOM MK808 Manual Download

Page: 122 / 168

115

MaxiVCI Mini Update

Update via Display Tablet

Before updating the VCI software, ensure the tablet

’s connection to the

Internet is stable.



To update the MaxiVCI Mini software

1. Power on the tablet.

2. Using a USB cable, connect the MaxiVCI Mini to the tablet.

3. Tap the

VCI Manager

application on the MaxiCOM Job Menu of

the tablet.

4. Select

Update

from the connection mode list.

5. The current version and the latest version of the VCI software will

be displayed after a few seconds. Click

Update Now

to update the

VCI software if available.

Update via PC

1. Down the Maxi PC Suite from

www.autel.com

> Support & Updates >

Firmware Downloads > Update Client, and install it onto your PC.

2. Using a USB cable, connect the MaxiVCI Mini to a PC.

3. Launch the

PC Suite

on the PC which is installed after the installation

Maxi PC Suite

and click MaxiVCI Mini icon in the Device Selection

window.

4. The PC will automatically recognize the MaxiVCI Mini.

5. Click

Update

to complete the update if an update is available.

Summary of Contents for MaxiCOM MK808









































































































































































Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands

Autel MaxiCOM MK808, Manual

Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands