Autel MaxiCOM MK808 Manual Download

Page: 23 / 168

Diagnostics

The Diagnostics application can retrieve ECU information, read & erase

DTCs, and view live data. The Diagnostics application can access the

electronic control unit (ECU) for various vehicle control systems, including

engine, transmission, antilock brake system (ABS), airbag system (SRS).

Establishing Vehicle Communication

The Diagnostics operations require connecting the MK808TS Diagnostic

Platform to the test vehicle through the MaxiVCI Mini. To establish proper

vehicle communication to the tablet, please perform the following steps:

1. Connect the MaxiVCI Mini to the vehicle

’s DLC for both communication

and power supply.

2. Connect the MaxiVCI Mini to the tablet via BT pairing.

3. A green check will display atop the VCI navigation button at the bottom

bar on the screen. If communication has been established, the
MK808TS is ready to start vehicle diagnosis.

Vehicle Connection

The tablet communicates with the vehicle via the BT connection provided by
the MaxiVCI Mini.

To connect the MaxiVCI Mini to the test vehicle, simply insert the Vehicle
Data Connector on the MaxiVCI Mini into the vehicle

’s DLC which is

generally located under the vehicle dash and the MaxiVCI Mini will be
automatically powered on.

NOTE

The vehicle

’s DLC is not always located under the dash; refer to the

vehicle

’s user manual for DLC location.

Summary of Contents for MaxiCOM MK808









































































































































































Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands

Autel MaxiCOM MK808, Manual

Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands