Autel MaxiCOM MK808 Manual Download

Page: 158 / 168

151



Search by the functions

1. Tap the

Function Viewer

application on the MaxiCOM Job Menu.

The Function Viewer application screen displays.

2. Tap the tool name on the top left to drop down the tool list, tap the

one you want to search.

3. Type in the function you want to search to the top right search

column. All the vehicles with this function will be listed with 8
columns, the Brand, Model, Year, System, Sub system, Function,
Sub function, and Version.

NOTE

Fuzzy search is supported, type in part of the function you want to search
can also find you all the related.

Figure 17-2

Sample Function Viewer Screen 2

Figure 17-3

Sample Function Viewer Screen 3

Summary of Contents for MaxiCOM MK808









































































































































































Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands

Autel MaxiCOM MK808, Manual

Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands