Autel MaxiCOM MK808 Manual Download

Page: 11 / 168

MaxiCOM MK808TS Display Tablet

Functional Description

1. 7.0

” LCD Capacitive Touchscreen

2. Ambient Light Sensor

– detects ambient brightness.

3. Power LED

– indicates battery level & charging or system status.

4. TPMS Service Symbol

– indicates the position of the embedded TPMS

antenna.

The power LED displays green, yellow or green depending on power level
and operating state.

A. Green



Illuminates green when the Display Tablet is charging and the
battery level is above 90%.



Illuminates green when the Display Tablet is powered on and the
battery level is above 15%.

B. Yellow



Illuminates yellow when the Display Tablet is charging and the
battery level is below 90%.

C. Red

Figure 2-1

Display Tablet Front View

Summary of Contents for MaxiCOM MK808









































































































































































Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands

Autel MaxiCOM MK808, Manual

Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands