Autel MaxiCOM MK808 Manual Download

Page: 108 / 168

101

images, the selected thumbnail displays a tick icon at the bottom
right corner.

5. Tap the

Delete

button, and then

Delete Selected

, then the

selected images will be deleted.

PDF Files

The PDF section stores and displays all saved data PDF files. Select a PDF
file from the database to display.

The standard Adobe Reader application is used for file viewing and editing,
please refer to the associated Adobe Reader manual for detailed
instructions.

Review Data

The Review Data section allows playback of the recorded data frames of
live data streams.

On the Review Data main screen, select a record file to playback.

Figure 7-3

Sample Data Playback Screen

1. Drop-down Toolbar

– tap the button at the top center of the screen to

open the Drop-down Toolbar.

2. Main Section

– displays the recorded data frames.

3. Navigation Toolbar

– controls data playback.

Summary of Contents for MaxiCOM MK808









































































































































































Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands

Autel MaxiCOM MK808, Manual

Search results

Summary of Contents for MaxiCOM MK808

Reviews:

Related manuals for MaxiCOM MK808

Brands by name

Popular brands