Atmel AT90S2333-8AC Manual Download Page 16 | Manualshive

Page: 16 / 103

background image

AT90S/LS2333 and AT90S/LS4433

16

Note:

Reserved and unused locations are not shown in the table.

All AT90S2333/4433 I/Os and peripherals are placed in the I/O space. The I/O locations are accessed by the IN and OUT
instructions transferring data between the 32 general purpose working registers and the I/O space. I/O registers within the
address range $00 - $1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the value of sin-
gle bits can be checked by using the SBIS and SBIC instructions. Refer to the instruction set chapter for more details.
When using the I/O specific commands IN, OUT the I/O addresses $00 - $3F must be used. When addressing I/O registers
as SRAM, $20 must be added to this address. All I/O register addresses throughout this document are shown with the
SRAM address in parentheses.

For compatibility with future devices, reserved bits should be written to zero when accessed. Reserved I/O memory
addresses should never be written.

Some of the status flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on
all bits in the I/O register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions
work with registers $00 to $1F only.

The I/O and peripherals control registers are explained in the following sections.

$15 ($35)

PORTC

Data Register, Port C

$14 ($34)

DDRC

Data Direction Register, Port C

$13 ($33)

PINC

Input Pins, Port C

$12 ($32)

PORTD

Data Register, Port D

$11 ($31)

DDRD

Data Direction Register, Port D

$10 ($30)

PIND

Input Pins, Port D

$0F ($2F)

SPDR

SPI I/O Data Register

$0E ($2E)

SPSR

SPI Status Register

$0D ($2D)

SPCR

SPI Control Register

$0C ($2C)

UDR

UART I/O Data Register

$0B ($2B)

USR

UART Status Register

$0A ($2A)

UCR

UART Control Register

$09 ($29)

UBRR

UART Baud Rate Register

$08 ($28)

ACSR

Analog Comparator Control and Status Register

$07 ($27)

ADMUX

ADC Multiplexer Select Register

$06 ($26)

ADCSR

ADC Control and Status Register

$05 ($25)

ADCH

ADC Data Register High

$04 ($24)

ADCL

ADC Data Register Low

$03 ($23)

UBRRHI

UART Baud Rate Register High

Table 2. AT90S2333/4433 I/O Space (Continued)

I/O Address (SRAM Address)

Name

Function

«
...
14
15
16
17
18
...
»

Summary of Contents for AT90S2333-8AC








































































































Reviews:

No comments

Related manuals for AT90S2333-8AC

Brand: Gardena Pages: 17

Brand: Badger Meter Pages: 16

Brand: Icar Pages: 40

Brand: Icar Pages: 86

Brand: Icar Pages: 39

Brand: Kamstrup Pages: 36

FOUNDATION 3730-5

Brand: Samson Pages: 132

Brand: Samson Pages: 68

Brand: Samson Pages: 128

Brand: Samson Pages: 68

Brand: Samson Pages: 80

Brand: Haehne Pages: 44

Brand: EasyIO Pages: 17

Brand: SYCLOPE electronic Pages: 40

Brand: HEIDENHAIN Pages: 257

Brand: Advanced Control Technologies Pages: 3

Brand: National Instruments Pages: 18

ServeRAID M1215 SAS

Brand: IBM Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands