manualshive.com logo in svg

AT&T Merlin Legend MLX-20L, Operator'S Manual, Page: 24 / 152

Share
Download
AT&T Merlin Legend MLX-20L Operator'S Manual Download Page 24

About Your Direct-Line Console

Console Equipment

Your system supports various headsets and a headset

amplifier. This section describes each of these equipment

options. For information about the actual use of the

equipment, see the equipment’s accompanying
documentation.

NOTE:

Not all consoles allow the use of headset, handset, and
speakerphone at the same time. Check with your system
manager before
simultaneously.

Headsets

trying to use this equipment

Four headsets are available for use with your console:

■ 

The 

StarSet® Headset 

has a single ear tip and is worn

without a headband.

■ 

The 

Mirage® Headset 

has a single disk-shaped

receiver and is worn without a headband.

■ 

The 

Supra® Headset 

has a single disk-shaped

receiver and a headband.

■ 

The 

Supra NC® Headset 

has two disk-shaped

receivers and a headband.

1-12

Console Equipment

Summary of Contents for Merlin Legend MLX-20L

























































































































































Reviews:

No comments