AT&T Merlin Legend MLX-20L Operator'S Manual Download Page 144

Page: 144 / 152

Special Characters

The following table describes special characters. Ask your
system manager which special characters are needed and
when to use them.

Special Characters Table

Press...

See...

Means...

Drop

Stop. Halts the dialing sequence to allow the
system to respond.

Hold

Pause. Inserts 1.5 second pause in the dialing
sequence. Multiple consecutive pauses are
allowed.

Conf

Flash. Sends a switchhook flash. Must be the first
entry in the dialing sequence.

For Extension Programming only

(Ext

Program [Prog] ):

End of Dialing. Used to signal

the end of the dialing sequence or used to

separate grouped digits, for example, account
codes from number dialed.

End of Dialing. Used to signal the end of the
dialing sequence or to separate group digits, for
example, account code from number dialed.

D-2

Special Characters

Summary of Contents for Merlin Legend MLX-20L

























































































































































Search results

Summary of Contents for Merlin Legend MLX-20L

Reviews:

AT&T Merlin Legend MLX-20L, Operator'S Manual, Page: 144 / 152

Search results

Summary of Contents for Merlin Legend MLX-20L

Reviews: