manualshive.com logo in svg

Associated Research HypotULTRA 7800, Operation And Service Manual

Share
Download
Associated Research HypotULTRA 7800 Operation And Service Manual Download Page 30

 

 

 

25 

 

6. 

REAR PANEL HIGH VOLTAGE OUTPUT TERMINAL:  

2

nd

 high voltage output 

connector in parallel with the front panel connector. 

 

 

7. 

REAR PANEL RETURN TERMINAL:

 2

nd

 return output connector in parallel with 

the front panel connector.  

 

 

8. 

REAR PANEL CONTINUITY OUTPUT TERMINAL:

 2

nd 

continuity output 

connector in parallel with the front panel output.  

 

 

9. 

FUSE RECEPTACLE:  

To change the fuse, unplug the power (mains) cord and 

turn the fuse receptacle counter-clockwise. This will expose the fuse compartment. 
Please replace the fuse with one of the proper rating.

 

  

 

 

10. 

SCANNER OUTPUTS:  

Optional internal Scanner matrix that provides 8 

HV/Continuity/Return connections.  Please refer to the Options section of this 
manual for additional connection information. 

 

 

11. 

INPUT POWER RECEPTACLE:  

Standard IEC 320 connector for connection 

to a standard NEMA style line power (mains) cord.

 

 

 

12. 

CHASSIS GROUND (EARTH) CONNECTION:  

Connect this terminal to a 

good earth ground before operation.

 

 

 

 

 
 
 

Summary of Contents for HypotULTRA 7800















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands