manualshive.com logo in svg

Associated Research HypotULTRA 7800, Operation And Service Manual

Share
Download
Associated Research HypotULTRA 7800 Operation And Service Manual Download Page 139

 

 

 

134 

 

NE PAS CONNECTER TENSION OU DE COURANT AUX ENTRÉES DE SIGNAL, 
CELA POURRAIT PROVOQUER DES DOMMAGES AU CIRCUIT DE CONTRÔLE 

 
Remote Interlock 

HypotULTRA is equipped with a Remote Interlock feature.  Remote Interlock utilizes a 
set of closed contacts to enable the instrument’s output.  If the Remote Interlock 
contacts are open the output of the instrument will be disabled.  Remote Interlock 
could also be referred to as a remote system lockout

, utilizing “fail when open” logic.  

If the Remote Interlock contacts are open and the Perform Test icon is selected, a 
pop-up message will be displayed on the screen for two seconds.  The message will 
appear as follows: 
 

 

 
If the Remote Interlock contacts are opened during a test, the pop-up message will be 
displayed and the test will abort.  The hardware and has been configured to provide 
the interlock connections on pins 4 and 5 of the Remote Interface, Signal Input port.  
The instrument can still be used without the external interlock device as long as the 
Interlock Disable Key (38075 provided with unit) is plugged into the Remote Interface, 
Signal Input port.  If there is nothing connected to the Remote Interface, Signal Input 
port to provide a connection to the Remote Interlock, the instrument will not perform 
tests. 
 

Summary of Contents for HypotULTRA 7800















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands