Product Information
5
NXP-TPI/4 NetLinx Touch Panel Interface
Specifications (Cont.)
Rear Panel Components
(Cont.):
PC control:
• 2 PS/2 ports for Keyboard and Mouse control.
• 2 USB ports for Keyboard and Mouse control. The two Type-A USB ports can
connect up to two external keyboard or mouse devices for use with Virtual
PC applications.
- These ports can be used to communicate to a PC and transfer pass-thru
touch control from the external devices, thru the TPI/4, through the TP4-RGB
Type-B USB connection, to the target PC, and then back again.
VGA output:
• HD-15 VGA output connector with a maximum resolution of 1280 x 1024.
Ethernet 10/100 port:
• RJ-45 port for 10/100 Mbps communication. The Ethernet port automatically
negotiates the connection speed (10 Mbps or 100 Mbps), and whether to use
half duplex or full duplex mode.
• This device communicates with the NetLinx Master using the ICSP protocol
over Ethernet. This communication is reflected via the front ICSP LED.
Ethernet 10/100 LEDs:
LEDs that show communication activity, connections, speeds, and mode
information:
• A-activity - Yellow LED lights when receiving Ethernet data packets.
• L-link - Green LED lights when the Ethernet cables are connected and
terminated correctly.
ICSNet connectors:
• Two RJ-45 connectors that allow connection to an ICSNet Hub.
Stereo Output connector:
• Stereo output through a 3.5mm mini-jack (for use with external speakers).
PWR connector:
• 2-pin 3.5 mm mini-Phoenix connector.
TP4 Input Cards:
• Refer to
Appendix
section on page 133 for more detailed power consumption
information.
TP4-VID:
Install the TP4-VID input module into any input slot to connect video sources,
such as VCRs and DVDs. Four screws secure the module.
• Accepts Composite or S-Video input signals for scalable video windows.
• Input video types are: NTSC, PAL, and SECAM.
• Composite LED indicator (turns On when composite video input is detected).
• S-Video LED indicator (turns On when S-Video input is detected).
• Connectors include:
- BNC Composite Video Input
- S-Video video input
TP4-RGB:
Install the TP4-RGB input module into any input slot to connect RGB-type
sources such as VGA, SVGA, etc. Two black screws secure the module.
• Accepts RGBHV, RGBS (H/V), and RG
s
B.
• Accepts computer-level graphics for scalable video windows.
•
USB used for pass-through computer control
.
- Pass-thru must be enabled to control devices on the RGB card
when
other control devices are connected to the PS/2 and USB connectors on
the rear of the TPI/4 unit.
Refer to the commands in the
^KPS
and
^MPS
section on page 122.
• Connectors include:
- HD-15 D-Sub graphics input: This
connector used to route an RGB
(computer) signal to a target monitor or panel by using the connected
TP4-RGB card.
- USB Mouse/Keyboard port:
Type-B USB device port input connector
for pass-thru computer control (by connecting an external keyboard or
mouse device for use with different PC applications). The touch signal
information is sent to and from the PC via this two-way connector.
• Refer to the following Pixel Input field information for the supported
resolutions and refresh rates via the TP4-RGB card.
Summary of Contents for NetLinx NXP-TPI/4
Page 38: ...TPI 4 and Panel Interface Setup 32 NXP TPI 4 NetLinx Touch Panel Interface...
Page 60: ...Upgrading TPI 4 Firmware 54 NXP TPI 4 NetLinx Touch Panel Interface...
Page 138: ...Troubleshooting 132 NXP TPI 4 NetLinx Touch Panel Interface...
Page 147: ...Appendix 141 NXP TPI 4 NetLinx Touch Panel Interface...