![background image](http://html.mh-extra.com/html/amx/modero-viewpoint-mvp-8400i/modero-viewpoint-mvp-8400i_operation-reference-manual_2938039080.webp)
Setup Pages
66
MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom
Pressing the
Simple
or
Enterprise
buttons at the bottom of the
Information/Configuration
section open
an appropriate Wireless Security window for Simple Mode or Enterprise Mode. Simple Mode is best
used for smaller installations that use a single Master, such as for residences or smaller office
environments. Enterprise Mode is intended for installations that use multiple Masters, where a wireless
device may need to switch between multiple wireless access points connected to different Masters in a
network.
Wireless Settings Page (Cont.)
IP Settings (Cont.):
Active Roaming on
Channels 1,6,11
When enabled, the device is actively roaming on the channels 1, 6, and 11. By
default, Active Roaming is disabled.
Of all the frequency channels that are assigned for wireless, only three are
non-overlapping frequencies that do not interfere with each other.
Non-overlapping channels avoid the interference that can affect the signal.
Access Point MAC
Address:
This unique address identifies the Wireless Access Point (WAP) used by this
panel for wireless communication (read-only).
•
Site Survey
button: Launches the Site Survey page. The options on this page
allow you to detect (“sniff-out”) all WAPs transmitting within range of the
panel’s
NXA-WC80211GCF
Wi-Fi card.
Data displayed on the
Site Survey
page is categorized by:
-
Network Name (SSID
) - WAP names
-
Channel (RF)
- channels currently being used by the WAP
-
Security Type
- security protocol enabled on the WAP, if detectable
-
Signal Strength
- None, Poor, Fair, Good, Very Good, and Excellent
-
MAC Address
- Unique identification of the transmitting Access Point
• Refer to the
Using the Site Survey tool
section on page 19 for more detailed
information on the
SIte Survey
page.
• When communicating with a NXA- WAP200G, enter the MAC Address
(
BSSID
) of the target WAP as the Access Point MAC Address. Refer to the
WAP200G
Instruction Manual
for more information.
Information/Configuration:
•
Mode -
Displays the current Security Type selected via either the Simple or
Enterprise options.
•
Security Type -
Displays whether the currently used security type is
Simple
or
Enterprise
.
•
SSID -
Displays the currently used SSID of the target WAP.
•
Channel -
The RF channel being used for connection to the WAP (read-only).
•
Signal Level Value -
Displays the quality of the link from the wireless NIC to
the Wireless Access Point (direct sequence spread spectrum) in real time
(
None
,
Poor
,
Fair
,
Good
,
Very
Good
, and
Excellent
).Even when link quality is
at its lowest you still have a connection, and the ability to transmit and receive
data, even if at lower speeds.
Note:
“Signal Level Value” and “Signal Level” are applicable to RF connections
only. It is possible to have an RF signal to a WAP, but be unable to
communicate with it because of either incorrect IP or encryption settings.
•
Signal Level -
This bar graph demonstrates the strength of the current signal.
Simple/Enterprise:
• Opens either the Wireless Security: Simple Mode or the Wireless Security:
Enterprise Mode windows.
Summary of Contents for Modero ViewPoint MVP-8400i
