manualshive.com logo in svg

Alstom SHPM 101, Service Manual

Share
Download
Alstom SHPM 101 Service Manual Download Page 279

SERVICE MANUAL

R5888B

QUADRAMHO

Chapter 5

Addendum 2

Page 13 of 13

SIGNALLING CHANNEL CHECK (SCHEMES 02 to 07)

Signal receive at end A correct

Signal receive at end B correct

Test option 62 is used to send
Test option 41 is used to check the signal receive

TRIP TEST (Test option 88)

Select required SW switches to the right to
check breaker operation when reset is pressed.
Breaker(s) operation obtained

FINAL SETTING CHECKS

All switches agree with check list

ON LOAD CHECKS

Voltage correct

Phase rotation correct

CT/VT phasing check

Forward directional check

Reverse directional check

SWITCHES MOVED FOR LOAD CHECKS

K11

θ

Ph

K1

K2

Reset any switches moved and then insert normal bridging plugs.

Summary of Contents for SHPM 101

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands