manualshive.com logo in svg

alphatronics AlphaCom XL, Service Manual

Share
Download
alphatronics AlphaCom XL Service Manual Download Page 57

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 57/74 

APPENDIX A Installing the FLASH program 
 

To flash new firmware into the AlphaCom XL you need to use a software utility to flash the file into the 
microprocessor. The software utility is free of charge and is supplied to Alphatronics by the manufacturer of 
the microprocessor. Ask the service desk for a copy of the software utility. 
 
Installing the flash software utility is very easy. Install the fdt_3_06.exe file on your computer or laptop.  
Choose for standard installation and choose to install an icon on your desktop. When the window below 
appears on your screen, make sure the boxes USB Drivers and AutoUpdate are not selected. 
 

 

 
Start the Flash Development Toolkit Basic 3.06 software, after the installation procedure has been 
completed. If there is no icon on your desktop, you can find the software by going to start/program 
files/renesas etc.   
 
The procedure below only needs to be performed once after the program starts up. The next time you start 
the program the settings are known.  
 

 

 

Summary of Contents for AlphaCom XL











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands