manualshive.com logo in svg

alphatronics AlphaCom XL, Service Manual

Share
Download
alphatronics AlphaCom XL Service Manual Download Page 22

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 22/74 

Select the option „Use the following IP address‟ and enter 

192.168.0.49

 at the IP-address field and 

255.255.255.0

 at the subnetmask field. The default gateway field can be left empty. Press OK to save the 

changes. 

 

 

 
 

Programming the AlphaCom XL can be done using a commonly used web browser. Supported versions are 
Internet Explorer (versions 5 and 6), Mozilla Firefox (version 1.5) and Opera (version 8.5).  
 
Before programming, the dipswitches on the ALPHACOM XL have to be set to the correct positions. 
  

 

Set dipswitch 1 to OFF to ensure that the factory defaults are not programmed again. 

 

Set dipswitch 2 to OFF to ensure that access to the webserver can only be reached by entering the 
valid login name and password and also the local IP address / webserver port. Dipswitch 2 can set to 
ON (is not necessary) if you wish to access the web browser without a login name / login code and 
using the default IP address 192.168.0.48 (and webserver port 80).

*)

 

 

Set dipswitch 3 to ON, this makes it possible to access the web browser. If dipswitch 3 is set to OFF, 
it is not possible to access the web browser in any way.  

 

Set dipswitch 4 to OFF. 

 

*)

 Only set dipswitch 2 to ON to program a login name, login code and local Ethernet settings. After 

programming these details reset the AlphaCom XL and make sure dipswitch 2 is set to OFF. 
 

Attention: 

in this manual the examples shown use the standard 

IP address 192.168.0.48

 and 

web port 80

. 

 
 
 

 

Summary of Contents for AlphaCom XL











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands