manualshive.com logo in svg

alphatronics AlphaCom XL, Service Manual

Share
Download
alphatronics AlphaCom XL Service Manual Download Page 53

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 53/74 

Performing a firmware (bios flash) upgrade locally 

 
 
To upgrade firmware locally in the AlphaCom XL, the installer must have the following tools: 
 

o

 

computer with RS-232 port (or a USB to serial converter) 

o

 

serial programming cable (art.code. 003834). 

o

 

flash program FDT (Flash Development Toolkit) 

o

 

firmware update file 

 

Power down the AlphaCom XL transceiver 
 
Connect the serial programming cable between the computer and the „boxed header‟ J32 on the AlphaCom 
XL board. The boxed header can be found directly next to the relays and under the AL1 output. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 

 

 Figure 6:

 Connections for flashing firmware (bios-update) 

 

RS-232 connector for flashing 

Jumper J44 for „flash‟ mode 

Jumper J43 for normale „run‟ 
mode 

Jumper J40 for „flash‟ 
mode. 

Watchdog LED 
(green) 

Summary of Contents for AlphaCom XL











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands