manualshive.com logo in svg

alphatronics AlphaCom XL, Service Manual

Share
Download
alphatronics AlphaCom XL Service Manual Download Page 10

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 10/74 

Industry 

Security Class 

Regulations for Alarming / transmission 

1 

AL1 

2 

AL1 

3 

AL1 

3* 

AL2 

4 

AL2 

4* 

AL3 

 

Alarm transmission 

AL0 

None 

AL1 

Alarm transmission according to NEN EN 50136-1-
1 level AL1 

AL2 

Alarm transmission according to NEN EN 50136-1-
1 level AL2 

AL3 

Alarm transmission according to NEN EN 50136-1-
1 level AL2 accompanied with a back-up 
transmission channel according to level AL1 via a 
different transmission method (for example GPRS)  

 
 
The above information is based on the „Verbeterde Risicoklassenindeling VRKI 2007‟. For a full overview, 
see 

www.hetccv.nl

. 

 
If all parameters have been set correctly the AlphaCom XL can be used 

in all cases !.

 In a AL3 situation the 

GPRS module must be present. 
 
According to the EN50136-1-1 there are specific rules and regulations that also apply for alarm transmission 
over IP. The AlphaCom XL complies with regulations: D4, M4, T5, A3, S2, I3. A higher number indicates a 
better performance.  
 
The regulations for AL1 are: T2, T2, T2, D2, M2, S1, I2. 
The regulations for AL2 are: T4, T2, T3, D3, M3, S2, I3 
The regulations for AL3 are: primary transmission AL2 + back-up AL1 
 
Most of the features of the AlphaCom XL with respect to the above mentioned information are determined 
by the hardware design of the AlphaCom XL. It is therefore not necessary to fill in specific parameters to 
comply. The only point of consideration is the 

Supervision Interval

 (polling time) and the periodic 

testmessage, see 

Configuration IP dialer.

  

It is strongly recommended when using AL1 to program the 

Supervision Interval

 to a value not higher than 

900 (15 minutes) and for AL2 no higher than 90 seconds. 
 
The 

Periodic Testmessage

 is the automatic test message generated by the AlphaCom itself. In the Standard 

Settings this is not necessary. When the AlphaCom XL is used in a AL2 application this value must be 
programmed in the 

Backup Settings

 to 1440 minutes (the regulation states less than 1x per 25 hours). This 

setting will determine that the backup medium, even though it is not active, will send a message 1x per 24 
hours. With this combination, the AlphaCom XL complies with even the highest level AL3.  

Summary of Contents for AlphaCom XL











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands