manualshive.com logo in svg

alphatronics AlphaCom XL, Service Manual

Share
Download
alphatronics AlphaCom XL Service Manual Download Page 26

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 26/74 

Status screen

 

 

 

 
After you have logged in as the supervisor (admin) a status menu will appear on your screen. In the status 
menu information is displayed of the most important options in the AlphaCom XL. On the left-hand side of 
the status menu various menu buttons can be found. Via these menu buttons you can access the various 
submenu‟s to change settings. The various submenu‟s will be explained in the next chapters of this manual. 
 
The information displayed in the status menu is refreshed every 10 seconds to provide the most up to date 
information at all times. 
 
Possible status information displayed for the transceivers: 
 
Disabled:  

The transceiver is not configured. 

Not in use:  

The transceiver is assumed to be programmed as a backup transceiver and is not operational 
yet.. 

Busy:   

The transceiver is busy establishing a connection of sending a message. 

Ready:   

The connection is operational. There are no messages in the buffer. 

Error:   

There has been no connection with the central station for over 90 seconds

.

 

 

Summary of Contents for AlphaCom XL











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands