manualshive.com logo in svg

alphatronics AlphaCom XL, Service Manual

Share
Download
alphatronics AlphaCom XL Service Manual Download Page 30

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 30/74 

GPRS 
 
When using a GPRS connection extra settings are necessary. The extra settings are 

different per provider 

and also different per type of subscription

. These settings are provided by your telecom provider. The 

default settings are for KPN, a dutch telecom provider. Some examples are: 
 
Provider 

Name Access point (APN) 

Usercode

*

 

Password

*

 

KPN 

internet 

internet 

 

KPN 

internet 

KPN 

gprs 

Vodafone 

web.vodafone.nl 

vodafone 

vodafone 

Vodafone (residential) 

live.vodafone.com 

vodafone 

vodafone 

Vodafone (commercial) 

office.vodafone.nl 

vodafone 

vodafone 

Vodafone Blackberry 

blackberry.vodafone.nl 

vodafone 

vodafone 

T-Mobile 

internet 

tmobile 

tmobile 

T-Mobile 

internet 

 

 

Orange 

internet 

 

 

Ben 

internet.ben 

 

 

Mobistar 

mworld.be 

mobistar 

mobistar 

Rabo mobiel 

Rabo 

 

 

Rabo mobiel (unlimited) 

Rabo.extra 

 

 

Telfort 

Internet 

telfort 

telfort 

 

*) 

In the table above were nothing has been filled must also not be filled in, in the programming. Also do not 

use spaces! 
 
The settings mentioned above are based on information found on the worldwide web at the time this manual 
was made. It is however possible that providers change settings in the future due to changes in subscriptions 
of new subscription types. (APN – access point name) 
 
 
Always active 
 
The GPRS module is commonly used as a back-up connection for the primary LAN hard-wired connection. 
In this case it is possible to choose that the GPRS module will enrol itself into the GPRS network but will 
not send any data. By selecting the option „always active‟ the GPRS module is enrolled into the network and 
is standby to send data. Whether this is always free of charge differs per provider. Some providers only 
charge for data being sent. If this is the case it is advisable to select the option „always active‟. The GPRS 
module is enrolled into the network and ready to send data immediately. 
 
During a power up or after changing settings the AlphaCom XL will connect to the GPRS network to 
establish a connection with the network and check all settings. The results will be displayed in the status 
menu. When the name of the provider is displayed (for example NL KPN) this means that the GPRS 
connection is established and GPRS is used by the AlphaCom XL. „Not in use‟ means the GPRS connection 
was established during the last session but the connection is not in use by the AlphaCom XL. 
 

Summary of Contents for AlphaCom XL











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands