manualshive.com logo in svg

alphatronics AlphaCom XL, Service Manual

Share
Download
alphatronics AlphaCom XL Service Manual Download Page 38

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 38/74 

PSTN interface configuration

 

 

 

 
The PSTN input (CMK) simulates an analog telephone line. An analog dialer or security alarm system with 
integrated analog dialer can be connected directly to this input. The AlphaCom XL will simulate the analog 
alarm transmission to the central and receive the complete alarm message from the analog dialer. 
 
On the PSTN input (CMK) we strongly advise to only connect TBR-21 certified / tested products.  
In general when connecting non-certified / non-tested products there should be no problems. If you have any 
questions , please contact the Alphatronics helpdesk. Also an up-to-date list of products tested with the 
AlphaCom XL will be listed on the website (

www.alphatronics.nl

 / 

www.alphatronics.eu

).  

 
 
In the setting 

protocol

 you can select which protocol the analog dialer transmits that is connected to the 

PSTN input. It is not necessary to perform any changes to the settings in the PSTN dialer. Account number 
and telephone number settings in the analog dialer can remain as they are. 
 
Select the protocol that is used in the analog dialer. The following protocols are supported: 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for AlphaCom XL











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands