manualshive.com logo in svg

alphatronics AlphaCom XL, Service Manual

Share
Download
alphatronics AlphaCom XL Service Manual Download Page 11

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 11/74 

QUICK INSTALLATION GUIDE

 

 

The most simple situation were the ALPHACOM XL transceiver can be used is in the consumer market: the 
homeowner has an existing alarm system en has decided to step over to Voice over IP (VoIP) instead of his 
existing analog or ISDN telephone line. Due to the migration to VoIP the transmission of alarm messages 
from his alarm system to the central station do not work correctly or are unreliable. By using the 
ALPHACOM XL transceiver the existing alarm system can be left untouched and the alarm messages can be 
transmitted to the central station in an efficient and reliable way.  
 
The ALPHACOM XL transceiver is available in a pcb only version and also in a version in its own synthetic 
casing including power supply and battery backup. Assuming we use the pcb only version, the ALPHACOM 
XL can be mounted inside the casing of the alarm system, connected to a free LAN connection on your 
router of switch and it is ready to be connected and programmed.  
 

Preperation 

 

Before installing please ensure the following components are present: 
 

-

 

Alarm system with analog dialer  

-

 

12VDC power supply from your alarm system 

-

 

Router or switch with a free LAN connection 

-

 

A working internet connection 

-

 

A Laptop  

-

 

A cross-over network cable for programming 

 
Make sure the following details are available before you start installing: 
 

-

 

The protocol that the analog dialer of the alarm system uses 

-

 

The IP address and registration port of the RC-4001 IP receivercard or RX-5000 receiver in the 
central station  

-

 

The IP address of the (local) Gateway that needs to be programmed in the ALPHACOM XL 

-

 

The subnet mask of the local network 

 
Tip: instead of using a local IP address and a subnetmask, the AlphaCom XL can also be set to work with 
DHCP (factory default). In this situation the AlphaCom XL will ask the DHCP server of the network to 
provide it with an IP address and a subnetmask.  
 

Mounting 

 

-

 

Mount the ALPHACOM XL in a metal casing using the plastic pcb studs. It is recommended to 
mount the AlphaCom XL in the metal cabinet of the alarm system. The metal cabinet and ground 
connection of the power supply (alarm system) should be connected to a clean earth connection. 

-

 

If the analog dialer is still connected to the analog telephone line (or VoIP), disconnect the telephone  
line cable from the dialer.  

-

 

Connect the cable from the analog dialer of the alarm system to the CMK connection of   
ALPHACOM XL transceiver (see figure 2 

,page. 13

). 

-

 

Connect a Cross-over network cable to the LAN connection of the AlphaCom XL and the LAN  
connection of your laptop. 

- 

Set dipswitches 2

*)

 

**)

 and 3

***)

 to ON. 

-

 

Power-up the ALPHACOM XL transceiver. 

 

*)

  dipswitch 2 set to ON: Logging in is possible just by using the login-name (admin). Dipswitch 2 can be 

set to OFF if the login name and password have already been set in the web browser. 

 

Summary of Contents for AlphaCom XL











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands