Airstream Cumberland EXPERT LA, User Manual

Page: 21 / 92

72
EXPERT LA rev.00
EXPERT LA
12. MONITORING FUNCTIONS
12.1 Current Conditions
The current condition menu gives a quick view of
the actual conditions in the barn.
Select:
Main menu
• The current conditions (inputs and output)
are shown on screen. Use the arrow keys to
scroll the display.
Set Points
Min. Vent.
Vent/Inlet
History
Age/Mortal
Clean Mode
Start/Stop
Monitoring
Program
Selection
Setup
Time/Date
Current conditions
Use to navigate
Ambient Temperature 72.3 °F
Current Stage 2
Current Probe Set 1
Set Point 70.0 °F
Inside Humidity Low %
Outside Humidity Low %
Static Pressure .000 “WC
Outside T° High °F
Heating Stages xx
Clock Output xx
Vent/Inlet 1 Position 0 %
Vent/Inlet 2 Position 0 %
Running Prog: Program 1
Temperature Probe 1 72.3 °F
Temperature Probe 2 72.4 °F
Temperature Probe 3 72.3 °F
Temperature Probe 4 72.1 °F
Yesterday Water 1 0 Gal
Yesterday Water 2 0 Gal
Yesterday Water 3 0 Gal
Main menu
12.2 Run Time Histories
Monitoring menus contain the daily run time of the
feeders & heaters. The controller keeps these daily
run times in memory for 75 days and logs these
values into monitoring menus at midnight.
Select:
Main menu
Monitoring
Select the desired monitoring menu:
- Feeders
- Heaters
Resetting the run time of a feeder
To reset the run time of a feeder, select the
following menus then follow the prompts on screen.
Select:
Main menu
Monitoring
Feeders
Reset Run Time
Main menu
Monitoring
Heater
Heater 1 Run time 75 days
Use to navigate
Total 150 min
Today 25 min
May 02 200X 27 min
May 01 200X 30 min
21
EXPERT LA rev.00
EXPERT LA
Whisker switch
Whisker switches tell the controller when
natural ventilation curtains are sufficiently
opened. Select “Yes” to enable the whisker
switch input of each curtain or select “No”
if these switches are not used.
[This parameter is common to all programs].
Ramping in stage 1
Select “Yes” to activate the ramping func-
tion on stage 1 fans. This function allows
smoothing out transition between minimum
ventilation cycles and stage 1.
Purge
The purge function allows opening natural
ventilation curtains on a short period of time
to purge the air continuously. Select “Yes”
to enable this function.
Misting
The controller can control one misting out-
put. Select “Yes” to enable this output.
Misting output follows the set point
Operating temperatures of the misting out-
put can either be related to the set point –
which means the controller automatically ad-
justs them when the set point changes – or
they can be set as absolute values. Select
“Yes” if they follow the set point or select
“No” if they set as absolute values.
Accessible if the misting output is enabled above.
[This parameter is common to all programs].
Cool cells
The controller can control one cool cell out-
put. Select “Yes” to enable this output.
Backup relay
The controller can control one backup re-
lay. Select “Yes” to use a backup relay.
[This parameter is common to all programs].
Number of outputs
Select the number of ouptuts in use (16 or
32 outputs).
[This parameter is common to all programs].
Use age-based functions ?
Some functions of the controller are based
on the age of the animals (temperature
curve, controller programs and lighting pro-
grams). Select “Yes” to use age-based func-
tions or select “No” to disable them.
[This parameter is common to all programs].
Temperature curve
The temperature curve is used to change
the temperature set point over time. Select
“Yes” to use this curve.
Accessible if age-based functions are enabled above.
[This parameter is common to all programs].
Number of programs
The controller can use several temperature
programs. Enable the desired number of pro-
grams (1 to 3 programs)
[This parameter is common to all programs].
Switch program by Age / Out T° ?
The controller can automatically enable a
new program when the animals reach a cer-
tain age and/or as a function of outside tem-
perature. Specify what factor causes a
change in the program selection: “Age” and/
or “ Out T” . Answer “No” to both questions
if you do no want the controller to change
the program automatically.
[These parameters are common to all programs].
Main menu
Setup
User
Install.
Installation
Use to navigate
Use Curtain 1 Compens? Yes
Use Curtain 1 Whisker? Yes
Use Curtain 2 Compens? Yes
Use Curtain 2 Whisker? Yes
Use Ramping in Stage1? Yes
Use Purge? Yes
Use Misting? Yes
Mist Follow Set Point? Yes
Use Cool Cell? Yes
Use Backup Relay Yes
Number of outputs? 32
Use Age? Yes
Use Temperature Curves? Yes