AirLive A.DUO User Manual Download Page 155

Page: 155 / 191

7. Command Line Interface

AirLive A.DUO User’s Manual

148

Command> set ssid remotessid airlive2

Enable or disable SSID broadcast

nable

Radio1 broadcast enabled

11a

supera_no_turbo

supera_static_turbo

namic_turbo

_turbo

Radio1 radio mode: supera_no_turbo

et wireless channel

nel 36

Radio1 channel: 36

et beacon interval for wireless interface. For explanation on
ireless parameters, please refer to section 4.2.14

al 100

Radio1 beacon internal: 100

et rts threshold. For explanation on advance wireless parameters,

r to section 4.2.14

347

Radio1 RTS threshold: 2347

set broadcast <enable | disable>

Purpose:

Example:

Command> set broadcast e

set radio mode <radio mode value>

Purpose:

set radio mode t

supera_dy

Example:

Command> set radio mode supera_no

set channel <channel value>

Purpose:

Example:

Command> set chan

set beacon interval <range:20-100>

Purpose:

advance w

Example:

Command> set beacon interv

set rts threshold <range:0-2347>

Purpose: s
please refe

Example:

Command> set rts threshold 2

Summary of Contents for A.DUO
































































































































































































Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands

AirLive A.DUO, User Manual

Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands