AirLive A.DUO User Manual Download Page 60

Page: 60 / 191

4. Wireless and WAN Settings

AirLive A.DUO User’s Manual

4.2.12 Access Control (ACL)

Operation Mode -> Setup -> Access Control

The A.DUO allows you to define a list of MAC addresses that are allowed or denied to

access the wireless network. This function is available only for Access Point and AP Router

modes.

Disable MAC address control list:

When selected, no MAC address filtering will be

performed.

Enable GRANT address control list:

When selected, data traffic from only the

specified devices in the table will be allowed in the network.

Enable DENY address control list:

When selected, data traffic from the devices

specified in the table will be denied/discarded by the network.

To add a MAC address into the table, enter a Mnemonic Name and the MAC Address, and

then click Add. The table lists all configured MAC Filter entries.

To delete entries, check the corresponding Select boxes and then press

Delete Selected

Summary of Contents for A.DUO
































































































































































































Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands

AirLive A.DUO, User Manual

Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands