AirLive A.DUO User Manual Download Page 103

Page: 103 / 191

4. Wireless and WAN Settings

AirLive A.DUO User’s Manual

4.7 WISP Specific Settings

In WISP mode, the AP will behave just the same as the Client mode for wireless function.

However, router functions are added between the wireless WAN side and the Ethernet LAN

side. Therefore, the WISP subscriber can share the WISP connection without need for

extra router.

WISP mode acts both in AP and Router which included in these operation modes: AP +

WISP and WISP + AP.

In WISP + AP mode, the Radio 1 is actually a wireless client of the WISP wireless node and

also the gateway of the local area network.

Gateway mode acts both in AP and Router which included in these operation modes: AP +

Gateway and G AP.

Summary of Contents for A.DUO
































































































































































































Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands

AirLive A.DUO, User Manual

Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands