AirLive A.DUO User Manual Download Page 159

Page: 159 / 191

7. Command Line Interface

AirLive A.DUO User’s Manual

152

7.5 En

Comman

nable | disable> upnp

e UPnP

UPnP with descDocUrl=http://192.168.1.1:80/BD.xml

ized.

ctory.

with descDocUrl http://192.168.1.1:49152/BD.xml

gistered.

nt. Listening for requests ...

Command> disable upnp

/disable SNMP

snmp

SNMP is enabled

Command> disable snmp

SNMP is disabled

able/Disable Commands

ds enable or disable settings

( enable/disable ): <e

Purpose:

To enable or disabl

Example:

Command>enable upnp

(Upnp)descDocName: BD.xml

UPnP Daemon: Intializing

UPnP Daemon: ipaddress=192.168.1.1 port=

UPnP Daemon: conf_dir_path=/var/upnp

Initializing UPnP SDK ...

UPnP SDK Successfully Initial

Setting the Web Server Root Directory to /var/upnp

Succesfully set the Web Server Root Dire

UpnpGetServerPort(): 49152

Registering the root device

IGD root device successfully re

Advertisements Se

Shutting down on signal 15..

UPnP is disabled

<enable | disable> snmp

Purpose:

To enable

Example:

Command> enable

Summary of Contents for A.DUO
































































































































































































Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands

AirLive A.DUO, User Manual

Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands