AirLive A.DUO User Manual Download Page 128

Page: 128 / 191

5. System Configuration

121

AirLive A.DUO User’s Manual

5.1.11 A.DUO Emergency Recovery

This section guides to recover your A.DUO system if the firmware crashed.

Download the tftp server to your PC. In the following example, we use tftpd32:

http://tftpd32.jounin.net/tftpd32_download.html.

Copy the tftpd32.exe of the downloaded file to C:\.

Change the IP address of your PC to 192.168.1.254 / 255.255.255.0

Copy the A.DUO firmware to C:\ and rename the firmware to

“zImage”

. Note that

the name must be zImage and no extension.

Connect A.DUO and PC with an Ethernet cable.

Run the tftpd32.exe. Note that the IP address must be 192.168.1.254.

Summary of Contents for A.DUO
































































































































































































Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands

AirLive A.DUO, User Manual

Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands