AirLive A.DUO User Manual Download Page 73

Page: 73 / 191

4. Wireless and WAN Settings

AirLive A.DUO User’s Manual

Check to
enable
Bandwidth
Control

Select Total
or Per User
control here

After enabling Bandwidth
Control and selecting
“Total” or “Per User” type,
click here to Apply

Settings for Per-User
Bandwidth Control

Settings for Total
Bandwidth Control

Enable Bandwidth

: Check to enable Bandwidth Control. Uncheck to disable it. The default

value is disabled.

You must select between Total Bandwidth and Per-User Bandwidth. They can not be

enabled at the same time.

Total Bandwidth

: Total Bandwidth control limit the bandwidth between

Wireless and Ethernet interface. Therefore, it is most suitable for

Client

Infrastructure Mode

Bridge Mode

, and

WISP Router Mode

. For WISP

operator who use A.DUO as the client side device; setting the Total

Bandwidth control on the A.DUO will easy the loading on the AP for

bandwidth management. To begin, please enable the Bandwidth

Management first. Then enter the downlink and uplink speed; click on Apply

to finish.

Summary of Contents for A.DUO
































































































































































































Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands

AirLive A.DUO, User Manual

Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands