AirLive A.DUO User Manual Download Page 121

Page: 121 / 191

5. System Configuration

AirLive A.DUO User’s Manual

114

UPnP

: Click here to enable UPnP. It is recommended not to open UPnP for

security reason.

Syslog:

Syslog is an IETF (Internet Engineering Task Force - the Internet

standards body)-conformant standard for logging system events (RFC-3164).

When the A.DUO encounters an error or warning condition (ie., a log-in attempt

with an invalid password), it will create a log in the system log table. To be able to

remotely view such system log events, you need to check the

Enable Syslog

box

and configure the IP address of a Syslog daemon. When doing so, the A.DUO will

send logged events over network to the daemon for future reviewing.

Syslog server IP address:

System event messages generated by the wireless

access point will be sent to a Syslog daemon running on a server identified by this

IP address.

5.1.5 SNMP Settings

System Configuration -> SNMP Settings

This screen allows you to configure SNMP parameters including the system name, the

location and contact information.

Summary of Contents for A.DUO
































































































































































































Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands

AirLive A.DUO, User Manual

Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands