AirLive A.DUO User Manual Download Page 91

Page: 91 / 191

4. Wireless and WAN Settings

AirLive A.DUO User’s Manual

MPPE Encryption:

Used to enable or disable special MPPE encryption function.

Compression

: Used to enable compression function.

Local Account Management

User Name:

Specify authentication username.

Password:

Specify authentication password.

Assign IP:

Specify the IP address of PPPoE client. If 0.0.0.0 is specified, then

PPPoE client will get an IP address between remote start IP and remote end

IP.

4.6.3 PPPoE Server Setup Example

In this exercise, we will setup 2 PPPoE Server Accounts in A.DUO according to the
Topology Diagram below.

PC1

IP address:

192.168.20.2

Subnet mask:

255.255.255.0

Default gateway:

192.168.20.1

DNS server:

192.168.20.1

A.DUO

SSID:

pppoe

WAN IP address:

192.168.20.1

LAN IP address:

192.168.1.20

Summary of Contents for A.DUO
































































































































































































Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands

AirLive A.DUO, User Manual

Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands