AirLive A.DUO User Manual Download Page 129

Page: 129 / 191

5. System Configuration

AirLive A.DUO User’s Manual

122

The name of firmware must change
to zImage and must be in C:\ (The
same folder as running tftpd.exe)

Power on A.DUO, the

“Status”

LED will light on after 3 seconds.

Push the

“Reset”

button until the

“Status”

LED off and on again and release the

“Reset”

button.

If the above process success, the A.DUO LAN LED keep flashing and the tftp serve

shows file download information.

10.

It takes around 5 minutes to download firmware and around 5 minutes to update

the firmware.

11.

After a successful recovery, the A.DUO boots up automatically.

12.

Try access 192.168.1.1, or the IP address you had changed before.

Repeat the processes again if failed.

Summary of Contents for A.DUO
































































































































































































Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands

AirLive A.DUO, User Manual

Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands