AirLive A.DUO User Manual Download Page 72

Page: 72 / 191

4. Wireless and WAN Settings

AirLive A.DUO User’s Manual

RADIUS Type:

RADIUS

Shared Secret:

This is used by your RADIUS server in the Shared Secret

field in RADIUS protocol messages. The shared secret configured in the

A.DUO must match the shared secret configured in the RADIUS server. The

shared secret can contain up to 64 alphanumeric characters.

RADIUS Server Reattempt Period:

The number of times the A.DUO should

attempt to contact the primary server before giving up

4.2.16 Bandwidth Control

Operation Mode -> Setup -> Bandwidth Control

Bandwidth Control can limit the maximum speed of entire wireless interface or individual

device. It is also known as Traffic Shaping. The A.DUO provides both Total Bandwidth and

Per-User Bandwidth Control for both uplink and downlink speed. It controls the speed of

both wireless and wired interface.

To configure, please click on the “Bandwidth Control” button under wireless settings. The

following screen will appear:

Summary of Contents for A.DUO
































































































































































































Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands

AirLive A.DUO, User Manual

Search results

Summary of Contents for A.DUO

Reviews:

Related manuals for A.DUO

Brands by name

Popular brands