manualshive.com logo in svg

AGCO LELY ATTIS PT 130, Operator'S Manual

Share
Download
AGCO LELY ATTIS PT 130 Operator'S Manual Download Page 87

GUID-1AA95066-BF5E-41BD-ADD3-F4F8F8398211-high.jpg [High]

Fig. 4  

To make sure that you lift safely use applicable equipment that obeys the specifications.
Before you lift the machine:
• The machine must be empty
• Lock all parts correctly to prevent movement
• Make sure that there is sufficient space for the machine
• Make sure that the ground is solid and can hold the weight of the machine (See the VIN plate on the

machine. Use the PTAC value or add the values A-0 and A-1 to calculate the weight of the machine).

6.3.2  Attach the machine to a truck

CAUTION: Risk of injury

Make sure that you use applicable equipment. If you do not, it can cause injury to persons
and damage to the machine.

The machine has specified points to hold it, if you

put the machine on to a truck.

GUID-F3CCA615-B72B-43E1-B12D-BB68152C4814-high.jpg [High]

Fig. 5  

GUID-6246A6F9-2640-499F-8753-36FA90580F9D [V1]

6. Specifications

Bale Wrapper 

87

4820.LE.EN01

Summary of Contents for LELY ATTIS PT 130



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands