manualshive.com logo in svg

AGCO LELY ATTIS PT 130, Operator'S Manual

Share
Download
AGCO LELY ATTIS PT 130 Operator'S Manual Download Page 48

2.

Move the loading arm to the transport

position.

3.

Turn "OFF" the E-link basic controller.

4.

Switch "OFF" the engine and remove the

ignition key.

GUID-AD2B8C15-0114-4094-A44F-189784645E90-high.jpg [High]

Fig. 18  

5.

Install the lock pin in to the loading arm, and

install the R-clip.

6.

Turn "OFF" the hydraulic system.

GUID-AAD336B2-5D34-4596-B01D-0FF7D2F73EC3-high.jpg [High]

Fig. 19  

3.3.3  Place or remove the wheel chocks.

Procedure

1.

Park the machine on solid ground when it is not in use.

2.

IMPORTANT: 

When the machine is not in

use and not connected to the tractor, the

wheel chocks must be in position.

Collect the wheel chocks from the storage

area of the machine and put them in position

behind each transport wheel.

GUID-61252C8C-99E0-4AE3-BD4C-AC6CD3D47149-high.jpg [High]

Fig. 20  

GUID-68223646-E59D-410B-BE23-AFD439BCE296 [V1]

3. Operation

48

Bale Wrapper

4820.LE.EN01

Summary of Contents for LELY ATTIS PT 130



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands