manualshive.com logo in svg

AGCO LELY ATTIS PT 130, Operator'S Manual

Share
Download
AGCO LELY ATTIS PT 130 Operator'S Manual Download Page 15

Key

Decal

Description

1

Warning: Risk of injury and entanglement

Keep out of the range of all machine parts that turn

during operation.

2

Warning: Risk of injury

Keep out of the bale release area. A safe distance is

more than 3 m.

3

Lift point.
Install the jack at this point to lift the machine from the

ground.

4

Warning: Risk of impact

Keep out of the area of the wrapper table. A safe

distance is more than 3 m.

5

Warning: Risk of electrical shock

Keep a sufficient distance (more than 3 m) away from

electrical power lines.

6

Caution: Risk of injury

Read the operator manual fully before you first use,

operate or do work on the machine.

7

Caution: Risk of injury

Stop the tractor engine and remove the key before you

do work on the machine.

8

Important: Damage to the machine

Maximum of 30 RPM for the wrapper table.

9

Warning: Risk of fire

Do not smoke near the machine.

4

1. Safety

Bale Wrapper 

15

4820.LE.EN01

Summary of Contents for LELY ATTIS PT 130



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands