AGCO LELY ATTIS PT 130 Operator'S Manual Download Page 45

Page: 45 / 98

Connect the safety towing chain between

the machine and the tractor.

Remove the dust caps from the two

hydraulic hoses.

10.

Connect the 3/8" hydraulic hose to a single-

acting hydraulic valve on the tractor.

11.

Connect the 1/2" hydraulic hose to a

connection without pressure on the tractor.

12.

Connect the lighting cable to the applicable

connection on the tractor.

13.

Make sure that the lights on the machine

operate correctly.

14.

Connect the electrical cable to the E-Link Basic controller.

GUID-B4E13FCE-D8DE-43EC-B2EB-94248C1E776C-high.jpg [High]

Fig. 12

15.

Move the parking jack to the highest position

and lock it.

GUID-A1BCE3BF-558F-47CB-A190-25D6D8037E20-high.jpg [High]

Fig. 13

16.

Collect the wheel chocks from behind the

transport wheels and put them in the storage

area on the machine.

GUID-1BD0AF60-9DD2-4356-9FB0-589B4506F4EB-high.jpg [High]

Fig. 14

3.2.2 Calculate the maximum permitted vertical load on the coupling point

Before starting the procedure

The vertical load on the coupling point must be less than the maximum permitted vertical load on the

coupling point.

GUID-4ADBEED2-C5A5-4718-A36D-7503974F2B5C [V2]

3. Operation

Bale Wrapper

4820.LE.EN01

Summary of Contents for LELY ATTIS PT 130


































































































Search results

Summary of Contents for LELY ATTIS PT 130

Reviews:

Brands by name

Popular brands

AGCO LELY ATTIS PT 130, Operator'S Manual

Search results

Summary of Contents for LELY ATTIS PT 130

Reviews:

Brands by name

Popular brands